\\r\\n
The 4 way engine mount tool will fit direct to your flywheel and in most cases can be used without you...
Leak down kit for testing air leaks for Luna , Lui, Vega & J comes with exhaust blanking/sealing plate...
MB Leak down kit for testing air leaks for series 1, 2, 3 and Gp/Dl. comes with both exhaust blanking...
Engine mount (silent block) removal & fitting tool.... BGM
Fork spring compressor for series 1, 2, 3 & Gp that is completely easy to use on its own. Simply protect...
Self powered Strobe timing light for setting ignition timing this uses its own battery to run it and...
Crank shaft extracting tool. Made by Mb.. instructions: The tool is bolted on the crankcase side, fit...
Steering tool set made by Mb scooter.. Beautifully Chromed two piece set .
Bridge bracket used to fit a dial gauge when you are setting up your front sprocket to the rear sprocket...
Engine mount (silent block) removal & fitting tool. MB
Clutch Compressor, for series 1,2 & 3. made un the UK
Rear hub puller for both early series1, 2 and series 3 sx/li/tv/gp rear hubs... made by Mb..
Clutch Compressor, for series 1,2 & 3. This mounts across 2 studs on the crankcase side, so it lines...
Steering bearing race fitting tool. for series 1, 2, 3 & Gp/Dl scooters. made by MB
Crankcase side kickstart modification tool. This will safely machine the side casing on Series1, 2 and...
Tool one for pulling crankshafts into place for for ALL Lambretta S1 + S2 + S3 + GP DL + Serveta's models....
Assembly and disassembly tool for gear selector. Tool for fitting the gear selector on the layshaft on...
Drive side bearing fitting and removal tool. Use one way and the tool easily pushes out the bearing....
Rear hub bearing fitting and removal tool. Use one way and the tool easily pushes out the bearing and...
Drive side bearing tool, tool to drift in the main driveside bearing.. MB scooters
Fork spring compressor tool Lambretta J Range + Lui Vega Cometa Instructions for use of the tool B216...
Flywheel & clutch holding tool. Granturismo
Digital multimeter -CTM-REV "Check-202" 2V - 250V- with rubber holster, and sound buzzer when testing...
Clutch spring aligning tool BGM superstrong clutches.
New Design fork spring compressor. The screws now lock into the forks with no wobble and allows the fork...
Extractor tool for removing the CasaCooler bearing support bush X218..
15mm piston circlip tool for 16mm piston circlips. Casa Performance X234
Jack for raising and supporting the engine when changing rear wheel....
Flywheel holding tool that will hold 90% of Lambretta flywheels. It is double ended and will hold normal...
16mm piston circlip tool for 16mm piston circlips. Casa Performance X233
Dial Gauge bracket, this bracket sits on top of the cylinder to hold a DTI gauge to set TDC... made by...
BGM Spark Plug socket Knurled finger grip to remove plug when hot 13mm Hexagon head so you can use a...
Drive Sprocket Sleeve removing pulling tool. re-made by MB Scooters. Works on Series 1, 2 and 3 moto...
Clutch spring aligning tool for when fitting clutches. This is for standard type clutches NOT BGM Su...
Vape ignition flywheel holding tool for all types of Lambretta Vape Ignition Systems
Crankshaft inner bearing sleeve fitting tool.
2 in a room, double ended carburettor removal tool. One end for sh20 and the other for sh22.. Carb not...
BGM Clutch holding tool that Holds the inner and outer clutch bell/housing so that the clutch nut can...
This tool is designed to remove the two fork link bushes. It s stepped to allow the inner one to be removed...