155 product(s) found for "Engine parts, cylinder & crank"
Engine Bar - X89K Offset Cones
X89K FLAT ONE SIDE main engine bolt set and a pair of CP off-set cones + 2 washers + nyloc nut set. Casa...
Cylinder Stud Set 165mm
165mm Cylinder stud set, made in high tensile 10.9 steel Longer than standard M8 15mm thread - 110mm...
Engine Mounts 3 Hole SCOOTOPIA
Scootopia 3 Hole engine mounts (silent blocks) very high quality made by Scootopia ..sold in pairs.....
Chain Case Nut & Wavy Washer Kit ST ST
Engine side case fixing kit stainless steel.. contains: m6 Nut x 14 m8 Nut x 2 m6 Wavy Washer x 14 m8...
Crankcase side Level Plug st/st MB
MB crankcase side level plug made in stainless steel c/w fibre washer.... fits: Series 1 Series 2 Series...
Cylinder Stud Set Rolled
160mm Cylinder stud set, made in high tensile steel Longer than standard M8 25 - 110 - 25
Casa Performance Seal Plate S1,S2,S3 & Gp/Dl
This is the 'SuperSeal' drive side oilseal aluminium retainer plate for all Lambretta S1 + S2 + S3 +...
Mag Housing Sealing Plate Stud Kit
Mag housing sealing plate Stud kit. The kit includes: 2 stainless steel studs. 2 nyloc nuts. 2 wavy ...
Viton Double Lipped Drive Side Oil Seal Casa
Drive side Casa High quality Italian made VITON double lipped oilseal 33 x 50 x 6 for all Lambretta S1...
Drive Side Oil Seal Plate MB inc Screws
MB drive side oil seal plate including allen type fixing screws.
RT Cylinder Head Stud
Specially designed stud to be used as an upgrade on Race-Tour type cylinders to secure the head instead...
Kickstart Oil Seal Racetour
Kickstart oil seal.. Fits all Series 1, 2 & 3 engines. Mb RaceTour brand..
Engine Bump Stop Washer
Engine bump stop washer..this fits underneath the bump stop rubber on the engine case.
Small Mag Oil Seal Racetour
Small mag oil seal.. Fits all Series 2 & 3 but not series 1 engines. Mb RaceTour brand..
Engine Mounts BGM
BGM Engine mounts sold in pairs,these fit all Lambretta engine casings - Series I, 2, 3 and Gp/Dl. Marked...
Piston Shim 1mm
1mm piston shim used on gudgeon pins to take up end float on standard pistons. 2 needed per piston.
Grease Nipple, 6mm, Stainless Steel, Original spec, MB
6mm MB Stainless steel grease nipple, used on some Lambrettas on the front hub backplate, the fork links...
Short Inlet Stud 7 x 34 st/st MB
Short inlet stud. 7 x 12-10-12 x 21mm in stainless steel made by MB..
Rear Hub Plate Stud 6 x 21 st/st MB
Rear hub plate stud, this stud tholds the rear hub bearing plate. can also be used to convert a gp gear...
Mag Housing stud 6 x 25 st/st MB
MB mag housing stud, this stud fits in the engine case to secure the mag housing. can also be used for...
CrankCase And End Plate Dowel
Dowel that locates the end plate to engine case and also locates the chain case to the main engine case,...
Drive Side Oil Seal Plate Screw Kit
4 slot head screws (standard Innocenti) that hold the drive side oil seal plate in place. These are the...
Grease Nipple M6
M6 grease nipple ..correct shape, 8 needed for series 1 & 2 models, 6 needed for series 3 models....
Woodruff Key
Woodruff Key....Good quality Italian made crank shaft key, fits in the slot to locate flywheel to the...
