\\r\\n
Rear Hub Cone Washer 1mm(0.9mm) Thick, in stainless steel.. made by MB
1.7 mm Clutch shim..MB precision clutch shim remade in hardened shim steel....
Flywheel holding tool that will hold 90% of Lambretta flywheels. It is double ended and will hold normal...
Headset wiring clip/clamp that holds the cables inside the headset in stainless steel.. made by MB..
MB Push in fork buffer set for Gp/Dl and late SX.. comprising of 2 thin & 2 fat rubbers..remade to a...
Fork spring stops, remade in nylon, which go up inside the forks..
Sealing plate grommet on top of mag house where stator wires go through LARGE Type.
Rear brake cable clamp/guide that sits under the gear and clutch adjuster block remade as original in...
Rear shock half nut and wavy washer kit in stainless steel from MB....
Viton PH Choke/starter jet O ring. MB
Mb St St top fork lock washer .. sits between the lock ring and the top bearing ring....
MB Gear Swivel Pivot Base. Gear swivel pivot base in stainless steel made by MB. The pivot base comes...
AC DC or AC/DC Ignition Switch The MB 'FIT ALL' Lambretta Ignition switch, the most advanced ignition...
125 150 175 185 and all small block inlet size cylinders inlet Gasket that is made f rom a White High...
MB Petrol tap lever adjuster/extension sleeve in stainless steel made by MB. this clever little sleeve...
Side panel spring clip plate rubber, for Gp/Dl and late clip on type panel scooters.. made by Mb Scooters...
7mm to 6mm oversized stud to repair a damaged exhaust tail pipe stud thread in stainless steel...
PHBH Carb mounting rubber for 26-30mm Dellorto PHBH, VHSH carbs.. made by Mb.
Adjustable Bottom chain guide for different sprocket combinations... made by Mb..
Dellorto PHBH MB upgrade kit to help with the issues of modern fuels. The kit comes with; Fuel resistant...
X13/2 Dellorto Needle, PHBH, MB This needle is only suitable for the PHBH range 26 - 30mm carburettors....
1.4 mm thick gearbox shim..MB precision gearbox shim remade in hardened shim steel.
MB mag housing sealing kit. The kit includes: stainless steel sealing plates, gasket, spit rubber grommet,...
Mag housing stud and fixing set, these hold the mag house in place. made by MB..
Race-Tour 195 cylinder kit. includes: Alloy cylinder. 65mm Meteor CAST coated piston kit. CNC cylinder...
Mb rear hub bearing O ring seal.. fits in the recess in the bearing to form a better seal..
Extra long cable adjuster screw for large carburettors made by MB scooters.. These will fit all the Dellorto...
1.2mm thick head gassket for Race Tour 195 (65mm bore) cylinders.
Oversize headlight rim screw in stainless steel 3.5 x 22mm, special 1st oversized screw with locating...
MB Headset cable guide in stainless steel for series 1,2,3 and Gp/Dl, these hold the Front Brake and...
MB Kickstart return spring for all series 3 & Gp/Dl ..
MB kickstart 4 piece shim set in zink.. comprising of. 1.0 mm 1.5 mm 1.75 mm 3.00 mm
MB 5 x 12 Extended flywheel and cylinder cowling screws in stainless steel made with a longer hex to...
MB Stator Plate Wiring Clip/clamp. Stator wire retaining clip,,secures the wires from the stator to the...
Brake shoe post set for front or rear Sx/Li/Tv/Lis and series 2 type brakes, these have groove/oilways...
Chain tensioner/slipper locking plate. This is used to spread the load from the two studs that hold the...
1.0mm laser cut aluminium packing plate for 150cc type casings. For use with cranks with 110mm long conrods...
Earth loom, Black MB designed earth loom to connect - the rear light - to regulator - to coil - and back...
MB stainless steel 8mm grease nipple used on some Lambrettas on the front hub (the turning part)....
1mm Shim that fits on the handle bar rod to take out any play....
0.3mm thick head gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes.
0.5mm thick fhead gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes....
Extended hub/wheel stud for sip tubeless type wheel rims made by MB in high tensile steel.
3mm MB Kickstart shaft shim. fits on kickstart shaft before the outer circlip..
Brass cups & stainless steel spring anti rattle set that fit inside the brake or clutch levers .... made...
MB brake adjuster Knurled stainless steel nut. fits front and rear brake adjusters.
MB Large clutch retaining circlip, designed by mb scooters to be a better fit.... may need slightly grinding...
Clutch Operating Arm that fits on chain case, made by MB.... remade in a hardened steel then zinc co...