\\r\\n
MB Speedo Drive Outer Screw. Threaded at both ends, one end to go into the hub and the other end for...
MB oversize (m8) brake and lever pin, made by MB Scooters.... If your lever holes are oval d and worn...
MB brake and clutch lever pivot pin in stainless steel, made by MB scooters....
Choke lever metal cap in stainless steel that sits at the rear of the choke unit..for all series 3, Gp/Dl...
Side panel spring clip (W clip) in stainless steel. For Series 3 scooters that use roller or loop type...
MB Speedo drive set as original remade in steel by MB for any Lambretta Series 1, 2 or 3....
MB rear adjuster assembly, completely made in stainless steel....
MB front adjuster assembly Li/Lis/Tv/Sx, completely made in stainless steel....
MB drive side oil seal plate including allen type fixing screws.
MB Rear Brake Pedal Overhaul in Kit in st/st.. 12mm shim brake pedal washer circlip spring nylon brake...
Filler breather cap. Made from stainless steel, designed by MB. Comes with a fibre washer and a length...
Air Hose Clip in stainless steel , for the top and bottom on 22mm air hoses and all hose sides that fix...
Air hose clip that fits the bottom of the air hose bellows rubber when using a standard 18/20mm carb...
Clutch arm spring..fits on clutch arm on chain case in stainless steel made by Mb Scooters..
GP & SX (late) stainless steel side panel spring clip set. made by Mb Scooters ....
MB Brake pedal return spring in stainless steel..for series 2,3 & Gp/dl...
0.5mm Handle bar rod shim that fits on the handle bar rod to take out any play....
1mm Shim that fits on the handle bar rod to take out any play....
MB crankcase magnetic drain plug made in stainless steel c/w fibre washer.... for series 1,2,3 Gp/Dl...
Set of 3 Tool box tie rods in stainless steel that hold the toolbox to the frame, for series 1,2,3 &...
MB crankcase side level plug made in stainless steel c/w fibre washer.... fits: Series 1 Series 2 Series...
Choke guide plate in stainless steel for all series 3 & Gp/Dl.... made by mb ..
MB Splash Plate for series 3 & Gp/Dl in a brushed stainless steel,excellent quality and fit. made by...
Special stainless steel MB designed plate to stop cables been cut through unlike the older Innocenti...
Rear brake cable clamp kit in stainless steel made by MB.
MB Fuel tank strap trunnion (TWO) set in stainless steel for series 1,2,3 and Gp.
MB Gear and clutch trunnion, this is a universal long type in st/st it comes with a small disc that goes...
Side panel spring clip plate in stainless steel for Gp/Dl and late Sx .... made by MB..
Fork cable spring clip in stainless steel for speedo and front brake cables on series 3 & Gp/Dl. MB ...
MB side panel spring clip brackets in stainless steel and are used to secure the W clip that holds the...
MB Stand & splash plate hook Set in st/st These clamps are to hold your stand to your frame. pressed...
MB Gear Swivel Pivot Base. Gear swivel pivot base in stainless steel made by MB. The pivot base comes...
MB Cable adjuster screw complete with nut, in stainless steel. Three needed per scooter....
TS1 reed block gaskets..There are two different size original TS1 inlet gaskets one small and one large,...
MB TS1 reed block gasket In a white ethanol resistant material.There are two different size original...
Fork spring stops, remade in nylon, which go up inside the forks..
Stainless steel washer that sits in your fork link to hold your spindle (and hub) in place Two needed...
Rear brake cable ferrule/top hat in stainless steel. mb scooters
2mm Rear Hub Cone Washer/shim in stainless steel.. made by MB
Rear Hub Cone Washer 1mm(0.9mm) Thick, in stainless steel.. made by MB
MB Clutch plates 1.0mm thick .. Sold individually. 3 needed for standard set ups. 4 needed for 5 plate...
MB Clutch arm shaft kit that fits both Li & Gp chain cases. MB Product
The ultimate tool for hassle-free engine mount (silent block) removal and fitting - the Engine Mount...