\\r\\n
Throttle dished washer for series 3 and Gp/Dl.
Series 1 and 2 throttle tube wavy/dished washer in stainless steel. MB
MB relieved cylinder stud. Relieved between thread ends to fit some cylinders that haven t been drilled...
Li125/Li150 series 3 throttle & gear control rod. This rod is made from stainless steel and been machined...
MB brake and lever pin, made by MB Scooters. These are as original in looks but made of stainless st...
Adjustable Bottom chain guide for different sprocket combinations... made by Mb..
S1 & 2 brass bush that fits in the end of the handle bars. MB
PHBH Carb mounting rubber for 26-30mm Dellorto PHBH, VHSH carbs.. made by Mb.
Clutch Operating Arm SHORT TYPE that fits on chain case, made by MB.... remade in a hardened steel and...
Speedo cable olive(bush) in brass that fits on the bottom of the speedo cable near to the hub....
Rear hub plain washer used with the recesses on 3 hole locking ring TL 4977
Chain case Gasket 1.2 mm thick, An upgraded thicker crankcase side gasket to fit all Series 1, 2 or 3...
MB kickstart 4 piece shim set in zink including oil seal and lugged type circlip. comprising of: 1.0...
1.4 mm thick gearbox shim..MB precision gearbox shim remade in hardened shim steel.
1.5 mm thick gearbox shim..MB precision gearbox shim remade in hardened shim steel....
Clutch Operating Arm SHORT TYPE that fits on chain case, made by MB.... remade in high tensile steel...
Mb reear hub bearing plate set of 3 in stainless steel .
MB kickstart 4 piece shim set in zink.. comprising of. 1.0 mm 1.5 mm 1.75 mm 3.00 mm
Mb rear hub bearing O ring seal.. fits in the recess in the bearing to form a better seal..
0.9 / 1.2 Mb rear hub bearing plate in stainless steel and has a recess on one side of 0.9mm recess on...
0.5 / 0.7 recessed Mb rear hub bearing plate in stainless steel
0.3mm Mb reear hub bearing plate in stainless steel and is flat on one side.
1mm MB Kickstart shaft shim. fits on kickstart shaft before the outer circlip..
1.75 mm MB kickstart shim in Zink.. fits on kickstart shaft before the outer circlip....
MB lazer cut kickstart shim 1.5mm thick. fits on kickstart shaft before the outer circlip.
PHBH One piece carb rubber to suit the MB shorty reed manifolds. Made from strengthened Viton rubber,...
End plate stud that is made longer one end (the end that locates in the engine casing) to give better...
Rear hub nut 3 hole type lock washer 6mm thick in stainless steel...
MB Rear hub nut 3 hole type lock washer 6mm thick in stainless steel including 3 m7 st/st allen screws....
Clutch Operating Arm that fits on chain case, made by MB.... remade in a hardened steel and hard chrome...
Mb rust resistant hardened steel hard chrome plated(chrome with out being polished before chroming) rear...
Brake pedal pivot bush in brass.... THIS IS FOR MB BRAKE PEDALS ONLY
S3 (special type) throttle & gear control rod for models - 125 special, TV, 150 special & SX (early type)...
MB Braided Lambretta extra long inner cable for larger carbs, for the Mb stainless friction free cables......
New type MB clutch inner cable made slightely thinner for a better clutch feel.
MB stainless steel Headset top screw for series 1,3 and Gp/Dl as original... holds the headset top and...
MB Throttle tube for Li & tv series 3(pre 1966) in stainless steel .. made by MB
MB Throttle tube for late series 3 & Gp/Dl (post 1966) in stainless steel .. this is for headsets with...
MB Large clutch retaining circlip, designed by mb scooters to be a better fit.... may need slightly grinding...
Rear frame badge holder and grill holder brackets for Series 3 scooters in stainless steel made by MB.......
Headset wiring clip/clamp that holds the cables inside the headset in stainless steel.. made by MB..
MB front brake adjusters remade in stainless steel, this version comes with a Brass knurled nut....
MB rear brake adjusters remade in stainless steel, this version comes with a Brass knurled nut....
Gp, Sx, Special late type Series 3 headset upgrade kit 2 x Headset rods, Gp, Sx, Tv, Special 125 late...
Set of 3 shims that take up play when fitting different type ignition switches in headsets. made by ...
MB mag housing sealing kit. The kit includes: stainless steel sealing plates, gasket, spit rubber grommet,...