\\r\\n
0.5 mm Mag housing gasket in a white fuel resistant gasket material. made by Mb
Small mag oil seal tool to drift in the small magneto housing oil seal.. made by MB scooters
Tap, 8mm diameter x 1mm fine thread pitch for cleaning out crank. Used for cleaning/tapping threads out....
1.3 mm Clutch shim..MB precision clutch shim remade in hardened shim steel....
1.9 mm Clutch shim..MB precision clutch shim remade in hardened shim steel....
1.5mm laser cut aluminium packing plate for 200cc type casings. For use with cranks with 110mm long conrods...
3.0mm cut aluminium packing plate for 200cc type casings. For use with cranks with 110mm long conrods...
SH22 Mixture screw & spring Dellorto & Scootopia SH22 carbs.
1.6 mm thick gearbox shim..MB precision gearbox shim remade in hardened shim steel....
S1, 3 & Gp Headset bottom quick fit screw set. Designed by MB and made in staineless steel. These screws...
25 Dellorto and 26/28/30mm Dellorto MB Leak down carb blank.
MB side panel spring clip brackets in stainless steel and are used to secure the W clip that holds the...
Tap, 7mm diameter x 1mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
MB TS1 reed block gasket In white ethanol resistant material. This fits up against the manifold and the...
MB TS1 reed block gasket In a white ethanol resistant material.There are two different size original...
1.8 mm Clutch shim..MB precision clutch shim remade in hardened shim steel....
Triangular HT Lead/cable rubber grommet....This rubber fits on your frame and secures the standard throttle...
Inlet manifold screw in stainless steel bolt inlet manifolds with larger carbs. This bolt is designed...
MB remade and re-designed rear hub cone that is 8 degree s to suit the later GP rear hubs and the modern...
Series 1 and 2 throttle tube wavy/dished washer in stainless steel. MB
MB brake adjuster Knurled stainless steel nut. fits front and rear brake adjusters.
MB Large clutch retaining circlip, designed by mb scooters to be a better fit.... may need slightly grinding...
Clutch Operating Arm that fits on chain case, made by MB.... remade in a hardened steel then zinc co...
1.4 mm Clutch shim..MB precision clutch shim remade in hardened shim steel....
These rubbers fit between the mount bracket and Regulators, Rectifiers or Regulator/Rectifier.. made...
2.4 mm thick gearbox shim..MB precision gearbox shim remade in hardened shim steel....
2.8 mm thick gearbox shim..MB precision gearbox shim remade in hardened shim steel....
Heavy weight Brass handlebar bush made by MB for the GP type throttle/gear rods using a 5mm roll pin....
0.7 thick head gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes....
MB horncasting rubber bead in BLACK. Remade & reshaped for easy fit for series 2, 3 &gp/Dl. fits between...
Fuel tank buffer set for series 3 Li, Sx, Tv & Lis. 8 Piece set.
Side panel spring clip (W clip) in stainless steel. For Series 3 scooters that use roller or loop type...
Brake shoe post set for front or rear Sx/Li/Tv/Lis and series 2 type brakes, these have groove/oilways...
Chain tensioner/slipper locking plate. This is used to spread the load from the two studs that hold the...
1.0mm laser cut aluminium packing plate for 150cc type casings. For use with cranks with 110mm long conrods...
Earth loom, Black MB designed earth loom to connect - the rear light - to regulator - to coil - and back...
MB uprated stainless steel engine mount(silent blocks) set. Fits all engine casings - Series I, 2, 3....
MB stainless steel 8mm grease nipple used on some Lambrettas on the front hub (the turning part)....
1mm Shim that fits on the handle bar rod to take out any play....
0.3mm thick head gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes.
0.5mm thick fhead gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes....
Extended hub/wheel stud for sip tubeless type wheel rims made by MB in high tensile steel.
3mm MB Kickstart shaft shim. fits on kickstart shaft before the outer circlip..
Brass cups & stainless steel spring anti rattle set that fit inside the brake or clutch levers .... made...
Extra long cable adjuster screw for large carburettors made by MB scooters.. These will fit all the Dellorto...
1.2mm thick head gassket for Race Tour 195 (65mm bore) cylinders.