\\r\\n
Geniune Dell orto needle valve with viton tip. For SH range of carbs. Replaces original part number 8145.....
X13 Dellorto PHBH carb needle. Diameter 2.50mm, tip 1.80mm, taper 22mm. The next weakest needle would...
BGM Flange type Inlet manifold bolt and washers. special length bolt to attatch inlet manifold to cy...
Rubber gasket for Dellorto SH series carburettor float bowls. Casa 470
115 Main Jet for Dellorto SH1/18, SH1/20, SH2/22 and Jetex Carbs. And pilot jet for phbh/phbl and some...
22mm carburettor, This is a remade version of the now discontinued Dellorto SH22 that was originally...
65 Main Jet for Dellorto SH1/18, SH1/20, SH2/22 and Jetex Carbs. And pilot jet for phbh/phbl and some...
SH 5899-2 Atomiser for Scootopia and Dellorto carbs. Originally fitted to Li150 Special, TV175, TV200,...
64 Main Jet for Dellorto SH1/18, SH1/20, SH2/22 and Jetex Carbs. And pilot jet for phbh/phbl and some...
Viton PH Choke/starter jet O ring. MB
Scootopia super fast flow petrol tap version 2. Designed with the internals of the tap to be much larger...
Flip choke for Vega Cometa SH20 type carbs as original.
Air Hose Clip, for the top of the air hose on an 18 or 20mm SH carburettor.. and fits at the top and...
Carburettor top bolt for SH1/18, SH1/20 & SH2/22 Dellorto & Scootopia carbs.
Viton PH Carb float bowl O ring. petrol resistant MB
X7/13 Dellorto Needle, PHBH, MB This needle is only suitable for the PHBH range 26 - 30mm carburettors....
BGM fuel hose. Clear anti kink hose.... Sold by the foot or multiples of 1 foot lengths....
PHBL 22-25 Flange type carb rubber to suit all Dellorto PHBL carbs 22 - 25mm, Fits 36mm spigot outside...
Carb refurb kit to fit all scootopia and 18,20 & 22mm dellorto carbs. float, bowl rubber gasket and needle...
Cable choke conversion kit for PHBH, PHBL, VHSA, VHSA, VHSB carbs.
Throttle cable adjuster rubber, this is for standard dellorto SH and Jetex carbs....
2.00 float needle valve for PHBH PHBL.
Ts1 reed block gasket,one small and one large needed to service....
Mb shorty reed valve gasket (white) to suit the MB shorty reed valve assembly's and also fits Malossi...
Mikuni tmx 35 carb rubber clip....
62 5mm Main Jet for Dellorto SH1/18, SH1/20, SH2/22 and Jetex Carbs. And pilot jet for PHBH/PHBL and...
360 degree Metal fuel banjo that turns all the way round for ease of fuel pipe routing, suitable for...
Solder nipple for throttle cables. Solder fitting -UNIVERSAL- fitting Ø=3.2mm x 3mm
Long inlet bolt m7 for bigger carb manifolds with wavy washer ... replaces the long inlet stud to make...
7mm nut in zink which can be used for gear adjuster screws, inlet and exhaust studs....
7mm spring washer in zink various uses, end plate, exhaust and inlet studs. 6 are required for the end...