\\r\\n
Chaincase, Gp/Dl type, in a highly polished finish made by UNI.. Best Available..
Engine side case fixing kit stainless steel.. contains: m6 Nut x 14 m8 Nut x 2 m6 Wavy Washer x 14 m8...
M6, Rear hub bearing stud for series 1,2,3 & Gp/Dl .. 4 required ....
Dowel that locates the end plate to engine case and also locates the chain case to the main engine case,...
TS1 225cc cylinder kit with Asso Piston including 70mm AF skimmed head (9.5:1 compression)....
Xtra long (45mm) M6 crank case stud, Ideal for hanging exhausts to.
4 slot head screws (standard Innocenti) that hold the drive side oil seal plate in place. These are the...
Set of piston rings (2) 2mm thick 57mm(150cc)....
Gp 58mm stroke 107mm conrod Road/Race crankshaft, with shimmed conrod made in Italy, teflon coated, high...
Long engine bar, this fits all models with the large engine mounts.... comes with 2 nyloc nuts and 2...
Flywheel cover in steel,black in colour . thinner type for standard length flywheel fins.
1mm piston shim used on gudgeon pins to take up end float on standard pistons. 2 needed per piston.
Engine bump stop rubber & washer for series 2,3 &Gp/Dl....
66mm piston kit for 200cc piston port cylinders. made in Italy....
Clutch arm O ring, this O ring sits on the chaincase where the clutch arm drops in .... its also used...
L shaped washer sits inside your magneto housing and holds one of the oil seals in place....
Woodruff Key....Good quality Italian made crank shaft key, fits in the slot to locate flywheel to the...
Rear hub bearing retaining plates....inner & outer ....
Scootopia 3 Hole engine mounts (silent blocks) very high quality made by Scootopia ..sold in pairs.....
Mag housing wire kit includes Two steel sealing plates, a gasket, a rubber grommet and fasteners...
4 screws that hold the drive side seal plate in place. I use these high tensile csk socket screws to...
Engine bolt frame cones for use with Sx/Tv/Lis and Gp/Dl type engines with the longer type engine mounts,...
Bare mag housing, New UNI .. fits li/sx/tv/Gp and can be used on Series 1 & 2... .
M6 grease nipple ..correct shape, 8 needed for series 1 & 2 models, 6 needed for series 3 models....
Mag housing sealing plate Stud kit. The kit includes: 2 stainless steel studs. 2 nyloc nuts. 2 wavy ...
High performance AF race crank, Gp 58mm with a 107 conrod. this made by AF Rayspeed and this is their...
Piston ring 66.0 (200cc) for 2 or 3 ring pistons made in Italy.
Mag house bearing spacer ring for li/lis/tv/sx bearings.
Engine side case allen screw & wavy washer fixing kit stainless steel..
Engine side case fixing kit stainless steel.. contains: m6 Nyloc Nut x 14 m8 Nyloc Nut x 2 m6 Flat Washer...
RB22 (225cc) cylinder kit with Asso piston including 9.75:1 head... cylinder kit for 200 block. FITTING...
RB20 cylinder kit with Wossner piston including 9.75:1 head... cylinder kit for small block. FITTING...
Chaincase, Gp/Dl type, Black powder coated embosed finish made by UNI.. Best Available..
Chaincase, Gp/Dl type, in a highly polished finish made by UNI.. Best Available..
70mmAF Mammoth cylinder head for 225cc AF Mammoth Head The New AF Mammoth Head is a direct replacement...
CasaCooler mag flange kit! It comes 101% complete and is plug n play for any standard Italian, Indian...
Granturismo 60x110 Gp taper crank. 18mm small end requires a STEP DOWN bearing for standard type pistons...
200cc Engine Case GranTurismo GT Intercontinental
Bare mag housing made by Scootopia .. fits li/sx/tv/Gp and can be used on Series 1 & 2.