\\r\\n
MB Gear Selector Spring. uprated gear selector spring ..gives a slightly more stiffer feel when changing...
Gear selector ball bearings that fit either side of the gear selector spring in the layshaft .... SOLD...
1mm MB Kickstart shaft shim. fits on kickstart shaft before the outer circlip..
Gear change arm for li/Sx/Lis and Tv.. zinc plated and comes with stainless steel screw and wavy washer....
Gear selector arm circlip,, the one that holds the tie bar on .
Locating pin that screws in the kickstart piston, tightens up by using an allen key... made by MB..
Bronze clutch bush with an oil groove machined in it...
kickstart rubber in GREY for series 1,2,3 & Gp/Dl.. made by Scootopia....
Clutch spider, one piece. For Series 1, 2, 3, Gp/Dl & Serveta. Casa M283
Clutch Pressure Pad. This fits in a GP crankcase side and is pushed out to actuate the clutch, remade...
Clutch pressure/bell Gp/Dl type..excellent quality and very well made.
7mm spring washer in zink various uses, end plate, exhaust and inlet studs. 6 are required for the end...
Side case oil level plug for series 1,2,3 and Gp/Dl as original.. Scootopia....
Magnetic Drain Plug for series 1,2,3 and Gp, Chrome plated brass, hex key fitting as original, c/w fibre...
Clutch plates 1.2mm thick .. Sold individually. 3 needed for standard set ups. 4 needed for 5 plate set...
Gear selector arm with the shaft and lever all in one. These can be used for series 2,3 and Gp engin...
Gear selector arm shaft, for Sx,Tv,Li and Lis..to be used with Casa gear arm These can be used for series...
End Plate fixing kit. 6 x High tensile screws 6 x Flat washers 6 x Spring washers
16 tooth BGM front sprocket. Chain Combinations: 15/46 80 Link Chain 16/46 81 Link Chain 17/46 81 Link...
17 tooth BGM front sprocket. Chain Combinations: 15/46 80 Link Chain 16/46 81 Link Chain 17/46 81 Link...
18 tooth BGM front sprocket. Chain Combinations: 15/46 80 Link Chain 16/46 81 Link Chain 17/46 81 Link...
BGM 19 T front sprocket. Chain Combinations: 15/46 80 Link Chain 16/46 81 Link Chain 17/46 81 Link Chain...
10mm E clip used for the GP clutch arm inside the chaincasing.
Gear cluster shim. series 1,2,3 & Gp/Dl. This shim sits between your casing and your gear cluster......
The shim that sits on the end of the layshaft, underneath the layshaft needle bearing....
This shim can be used on the gear arm, clutch arm, brake cam and rear brake pedal.
BGM Gear selector pawl set including circlips. made in Germany
Crankcase Breather/filler plug and fibre washer Casa B104
Clutch arm rod/shaft that fits inside the chain casing and the operating lever fixes to, for li,Tv,Sx...
Top bearing pressure plate insert LI type for AF road 6 plate clutch....
3 Piece gear cluster bearing and bush set, comprising of: Gear cluster bearing. Bush. Shim (fits under...
Gear selector arm/tie bar Stainless steel E clip.
High quality Clutch needle bearing.. Used as standard on Li, SX, TV models.. two needed
Clutch arm O ring, this O ring sits on the chaincase where the clutch arm drops in .... its also used...
Kickstart piston disc, this sits in the kickstart shaft where the kickstart piston goes behind the s...
Kickstart piston disc internal circlip. this sits in the kickstart shaft where the kickstart piston goes...
Gear selector fork M6 screw but with a smaller head, so you use a 9mm socket instead of a 10mm that you...
Magnetic drain, level & breather plug set with fibre washers..
Sx,Tv and Li series 1,2 & 3 clutch pressure/bell Thimble...
MB Large clutch retaining circlip, designed by mb scooters to be a better fit.... may need slightly grinding...