\\r\\n
Tap, 8mm diameter x 1.25mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
Tap ratchet T handle for smaller tap sizes. 3mm to 8mm tap sizes.
Powermaster clutch Special holding tool for holding the PowerMaster STD (art. X33s) clutch in place for...
Fork spring compressor for series 1, 2, 3 & Gp that is completely easy to use on its own. Simply protect...
35mm TMX Mikunis and 34/36/39mm Dellorto VHSB MB Leak down carb blank.
Multi purpose 8mm T handle screws. These are very useful and they can be used all the time on an engine...
Crankshaft inner bearing sleeve fitting tool.
Double sided flywheel Extractor/Puller for all Lambretta & Vespa models..
Large mag oil seal tool to drift in the in board (large) magneto housing oil seal . made by MB scoot...
MB Leak down exhaust blanking plate ROUND type.
Piston stop tool, universal for Lambretta & Vespa (short reach type)....
Rear hub bearing fitting and removal tool. Use one way and the tool easily pushes out the bearing and...
Rear hub puller for both early series1, 2 and series 3 sx/li/tv/gp rear hubs... made by Mb..
Tap ratchet T handle for larger tap sizes. 5mm to 12mm tap sizes.
BGM Clutch holding tool that Holds the inner and outer clutch bell/housing so that the clutch nut can...
Drive side crankshaft dummy bearing bush tool. Stainless steel so it won t rust This replaces a flywheel...
Mag side crankshaft dummy bearing bush tool. Stainless steel so it doesn t rust. This replaces a flywheel...
16mm piston circlip tool for 16mm piston circlips. Casa Performance X233
Tap, 6mm diameter x 1mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Front and...
Tap, 6mm diameter x 1mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
Vape ignition flywheel holding tool for all types of Lambretta Vape Ignition Systems
The 4 way engine mount tool will fit direct to your flywheel and in most cases can be used without you...
8 x 1mm right hand thread fine pitch for crankshaft drive side bolt threads series 1,2,3 & Gp
Drive side bearing fitting and removal tool. Use one way and the tool easily pushes out the bearing....
The ultimate tool for hassle-free engine mount (silent block) removal and fitting - the Engine Mount...
Tool for pulling the layshaft in. Offer the layshaft into the bearing, fit the sleeve locating the allen...
MB Leak down rxhaust blanking plate OVAL/BGM type.
Piston stop tool, universal for Lambretta & Vespa. Plastic ebd version.
Rear brake pedal and gear selector shaft bush removal Tool.. made by mb scooters
Clutch Compressor, for series 1,2 & 3. This mounts across 2 studs on the crankcase side, so it lines...
MB Leak down kit for testing air leaks for series 1, 2, 3 and Gp/Dl. comes with both exhaust blanking...
Spark Plug socket Knurled finger grip to remove plug when hot 13mm Hexagon head so you can use a spanner...
Tap, 3mm diameter x 0.5mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
Tap, 5mm diameter x 0.8mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
BGM "O" ring removal tool that can also be used for scribing ....
Extractor tool for removing the CasaCooler bearing support bush X218..
Tap, 3.5mm diameter x 0.5mm thread pitch, Used for cleaning/tapping threads out. Can be used for: Series...
Tap, 4mm diameter x 0.7mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...