\\r\\n
0.5mm thick fhead gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes....
1.0mm thick head gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes....
0.7 thick head gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes....
0.7mm thick head gasket for Race Tour 195 (65mm bore) cylinders....
1.0mm thick head gassket for Race Tour 195 (65mm bore) cylinders.
0.5mm thick head gasket for Race Tour 195 (65mm bore) cylinders....
0.3mm thick head gasket for Race Tour 195 (65mm bore) cylinders....
MB rubber side panel buffer for series 3 & Gp/Dl marked with MB on the flat side.. sold in pairs
Triangular HT Lead/cable rubber grommet....This rubber fits on your frame and secures the standard throttle...
Mb stainless steel shim fits on the gear pivot base beneath the swivel on standard type gear pivot bases....
RT195 Replacement pair of 65mm x 1mm Bgm piston rings for MBGM Race-Tour 195 cylinder kits. Also fits...
Mb Choke Lever Assembly for series 3 & Gp/Dl in stainless steel.
Cylinder head stud/fastener kit MB fastener upgrade kit for the MBgm Race Tour cylinder kits. The kits...
Mb brass olives, Mb stainless steel clamps & screw set, for series 1,2,3 & Gp/Dl.... 2 Mb Brass Olives....
Mb stainless steel headset olive clamps & screw set, for series 1,2,3 & Gp/Dl.... 2 stainless clamps....
Throttle and gear roller olive bush support clamp in stainless steel.... Two required per handle bar......
Set of 3 Tool box tie rods in stainless steel that hold the toolbox to the frame, for series 1,2,3 &...
MB Fork Drum brake Links. Fork links, drum type with damper stud lugs, these use GP rods, with nylon...
Split pin in stainless steel for connecting petrol tap lever to the petrol tap and the rear brake pedal...
Crankcase side kickstart modification tool. This will safely machine the side casing on Series1, 2 and...
25mm PHBL Dellorto and 24mm Mikuni carburetors to 200cc type cast cylinders (200cc Race-Tour, Factory,...
Rear brake cable clamp/guide that sits under the gear and clutch adjuster block remade as original in...
Rear runner support arm to suit all Series 3 & Gp/Dl right hand floor boards in a semi polished stainless...
MB mag housing sealing kit. The kit includes: stainless steel sealing plates, gasket, spit rubber grommet,...
Gear change bush made in brass by MB, this fits into the clutch housing....
MB longer exhaust port stud for round exhaust ports to suit the new longer stronger MB brass nuts.
Exhaust stud for oval ports to suit the longer MB brass nuts.
Extra long cable adjuster screw for large carburettors made by MB scooters.. These will fit all the Dellorto...
Exhaust 7mm Extended brass nut.. made by MB scooters.
MB Stator Plate Wiring Clip/clamp. Stator wire retaining clip,,secures the wires from the stator to the...
MB Petrol tank cap rubber seal for all standard Lambretta fuel tank caps in viton....
Petrol tap lever in stainless steel with adjuster sleeve and split pin to suit all Series 3 scooters.....
MB Petrol tap lever adjuster/extension sleeve in stainless steel made by MB. this clever little sleeve...
Side panel spring clip plate in stainless steel for Gp/Dl and late Sx .... made by MB..
MB Crankcase side stud, you need 14 for most crankcases. 6mm x 12 - 10 - 1mm in stainless steel, normal...
MB full set of stainless steel standard length studs with nyloc nuts and plain washers to secure your...
Clear Front damper gaiters to suit standard style dampers and the BGM thin hydraulic dampers.... CLEAR...
Front shocker gaiter damper rubber covers by MB to suit standard style dampers and the BGM thin hydraulic...
MB crankcase side stud,slightly longer that the standard crankcase stud by 4mm to allow the exhaust bracket...
Flywheel holding tool that will hold 90% of Lambretta flywheels. It is double ended and will hold normal...
MB Gear Swivel Pivot Base. Gear swivel pivot base in stainless steel made by MB. The pivot base comes...
Stainless steel rear nyloc nut to suit BGM rear shockers but good for all other makes too.. made by MB...
Heavy weight Brass handlebar bush made by MB for the GP type throttle/gear rods using a 5mm roll pin....
MB Brass heavy weight handlebar outer end bush for series 3, these help reduce vibration as well as smooth...
Clutch Pressure Pad. This fits in a GP crankcase side and is pushed out to actuate the clutch, remade...