\\r\\n
Regulator Rubber Cover.... Fits all Lambretta & Vespa 3 and 5 pin regulators.... MB Product
MB remade and re-designed rear hub cone that is 8 degree s to suit the later GP rear hubs and the modern...
Rear Hub Cone Washer 1mm(0.9mm) Thick, in stainless steel.. made by MB
MB made Rear hub nut in stainless steel. Slightely taller than standard so can accommodate any hub/layshaft...
MB made metal cones that sit in the two holes on your frame where the engine bar goes through the middle...
This kit contains the correct number of allen cap head screws and washers to fit your head and flywheel...
Rear hub locking ring screw M7 thats used to fix the rear hub nut lock washer to an Italian type rear...
Locating pin that screws in the kickstart piston, tightens up by using an allen key... made by MB..
MB Brake pedal return spring in stainless steel..for series 2,3 & Gp/dl...
Throttle and gear rod olive brass bush. MB.
MB Splash Plate for series 3 & Gp/Dl in a brushed stainless steel,excellent quality and fit. made by...
Bronze clutch bush with an oil groove machined in it...
Flywheel and head cowling screw kit in stainless steel that contains the correct number of hex set screws...
MB Stand & splash plate hook Set in st/st These clamps are to hold your stand to your frame. pressed...
MB brake and clutch lever pivot pin in stainless steel, made by MB scooters....
Stainless steel washer that sits in your fork link to hold your spindle (and hub) in place Two needed...
MB Rear Brake Pedal Overhaul in Kit in st/st.. 12mm shim brake pedal washer circlip spring nylon brake...
MB Gear and clutch trunnion, this is a universal long type in st/st it comes with a small disc that goes...
S3 & Gp Mesh fast flow Air Filter from MB. This filter allows the engine to breathe more freely than...
Lambretta Black AC or DC, universal two part wiring loom This comes with a normal AC loom and an extra...
Stainless steel studs designed for use with cylinders with oval exhaust ports (eg standard, Mugello,...
MB Cable adjuster screw complete with nut, in stainless steel. Three needed per scooter....
Anodised silver titanium look. Fit on top fork damper brackets to keep hydraulic and brake cables safe...
Crankshaft inner bearing sleeve fitting tool.
Crank fitting/pulling tool Fit the tool over the crank on the drive side side and then use your drive...
Bridge bracket used to fit a dial gauge when you are setting up your front sprocket to the rear sprocket...
MB Speedo Drive Outer Screw. Threaded at both ends, one end to go into the hub and the other end for...
25 phbl inlet manifold to suit small block 150cc stud spacing cylinders. MB Product
MB Speedo drive set as original remade in steel by MB for any Lambretta Series 1, 2 or 3....
Stepped carb rubber 26/28/30 phbh to mikuni tmx 35mm... made by Mb..
Clutch Pressure Pad. This fits in a GP crankcase side and is pushed out to actuate the clutch, remade...
MB Brass heavy weight handlebar outer end bush for series 3, these help reduce vibration as well as smooth...
Heavy weight Brass handlebar bush made by MB for the GP type throttle/gear rods using a 5mm roll pin....
Stainless steel rear nyloc nut to suit BGM rear shockers but good for all other makes too.. made by MB...
MB Gear Swivel Pivot Base. Gear swivel pivot base in stainless steel made by MB. The pivot base comes...
Flywheel holding tool that will hold 90% of Lambretta flywheels. It is double ended and will hold normal...
MB crankcase side stud,slightly longer that the standard crankcase stud by 4mm to allow the exhaust bracket...
Front shocker gaiter damper rubber covers by MB to suit standard style dampers and the BGM thin hydraulic...
Clear Front damper gaiters to suit standard style dampers and the BGM thin hydraulic dampers.... CLEAR...
MB full set of stainless steel standard length studs with nyloc nuts and plain washers to secure your...
MB Crankcase side stud, you need 14 for most crankcases. 6mm x 12 - 10 - 1mm in stainless steel, normal...
Side panel spring clip plate in stainless steel for Gp/Dl and late Sx .... made by MB..
MB Petrol tap lever adjuster/extension sleeve in stainless steel made by MB. this clever little sleeve...
Petrol tap lever in stainless steel with adjuster sleeve and split pin to suit all Series 3 scooters.....
MB Petrol tank cap rubber seal for all standard Lambretta fuel tank caps in viton....
MB Stator Plate Wiring Clip/clamp. Stator wire retaining clip,,secures the wires from the stator to the...