\\r\\n
Exhaust 7mm Extended brass nut.. made by MB scooters.
3mm MB Kickstart shaft shim. fits on kickstart shaft before the outer circlip..
Speedo cable olive(bush) in brass that fits on the bottom of the speedo cable near to the hub....
Oversize headlight rim screw in stainless steel 3.5 x 22mm, special 1st oversized screw with locating...
Oversize headlight rim screw in stainless steel 4 x 22mm, special 2nd oversized screw with locating peg...
Rear hub plain washer used with the recesses on 3 hole locking ring TL 4977
Side panel spring clip plate fixing set in stainless steel. For Series 3 & J.
0.5mm Magneto house gasket for series 1, 2, 3 & Gp/Dl. made by Mb
Mb GP/DL Cev Headlight bulb holder clip in stainless steel. TWO NEEDED made by Mb..
Stainless steel Rear light lense fixing screws for late series 2 and series 3.
1.0mm Magneto house gasket for series 1, 2, 3 & Gp/Dl. made by Mb
MB Lambretta Brake light switch rubber cover..this will fit 2 & 3 pin brake light switches including...
New type MB clutch inner cable made slightely thinner for a better clutch feel.
Rear number plate fixing kit for series 1 & 2 with stainless steel fixings..
MB shorty reed Inlet manifold screw in stainless steel.
Legshield end cap T nut in stainless steel. sits on the front of the legshields .. 2 needed for series...
Rear hub locking ring screw M7 thats used to fix the rear hub nut lock washer to an Italian type rear...
Mud flap stainless steel metal spacer bush that fits in the holes on the rubber mud flaps where they...
0.2mm gear cluster shim, This shim is used to shim the gear cluster when fitting 5 speed gear boxes.
0.5mm gear cluster shim, This shim is used to shim the gear cluster when fitting 5 speed gear boxes.
Stainless Square headed Bolt for fixing rear light unit to frame, Li/Sx/Tv/Lis Rear light units. 2 needed...
Rear shock spacer shim. these shims just offset the shock to give it a bit more clearance from the rear...
Round fibre Exhaust gasket for Ts1 Imola type exhausts made by Mb..
This kit contains the correct number of allen cap head screws and washers to fit your head and flywheel...
This rubber fits between the mounting point and coil, use studs, nyloc nuts and washers if you can (or...
MB Braided Lambretta extra long inner cable for larger carbs, for the Mb stainless friction free cables......
MB Stainless steel Handlebar gear support steel L washer for series 1,2 and late Indian GP
Throttle dished washer for series 3 and Gp/Dl.
MB Gear Selector Spring. uprated gear selector spring ..gives a slightly more stiffer feel when changing...
Flywheel and head cowling screw kit in stainless steel that contains the correct number of hex set screws...
Locating pin that screws in the kickstart piston, tightens up by using an allen key... made by MB..
1mm MB Kickstart shaft shim. fits on kickstart shaft before the outer circlip..
MB lazer cut kickstart shim 1.5mm thick. fits on kickstart shaft before the outer circlip.
1.75 mm MB kickstart shim in Zink.. fits on kickstart shaft before the outer circlip....
Clutch arm spring..fits on clutch arm on chain case in stainless steel made by Mb Scooters..
0.8 mm Clutch shim..MB precision clutch shim remade in hardened shim steel....
1.0 mm Clutch shim..MB precision clutch shim remade in hardened shim steel....
1.3 mm Clutch shim..MB precision clutch shim remade in hardened shim steel....
1.5 mm Clutch shim..MB precision clutch shim remade in hardened shim steel....
1.6 mm Clutch shim. MB precision clutch shim remade in hardened shim steel.
1.9 mm Clutch shim..MB precision clutch shim remade in hardened shim steel....
MB extra strong throttle spring for Dellorto PHBH. Improves the throttle slide shutting off even if you...
Front brake cable ferrule in stainless steal, made by Mb scooters....