\\r\\n
MB Braided Lambretta extra long inner cable for larger carbs, for the Mb stainless friction free cables......
Split pin in stainless steel for connecting petrol tap lever to the petrol tap and the rear brake pedal...
Head light rim screw ZINK FITS: Series 3 Sx, Tv, Specials & Gp/Dl
Head light rim screw in Stainless steel. FITS: Series 3 Sx, Tv, Specials & Gp/Dl
Exhaust stud for oval ports to suit the longer MB brass nuts.
MB Clutch plates 1.0mm thick .. Sold individually. 3 needed for standard set ups. 4 needed for 5 plate...
Gear selector arm/tie bar Stainless steel E clip.
Exhaust 7mm Extended brass nut.. made by MB scooters.
New type MB clutch inner cable made slightely thinner for a better clutch feel.
Stainless steel washer that sits in your fork link to hold your spindle (and hub) in place Two needed...
Chain case Gasket 1.2 mm thick, An upgraded thicker crankcase side gasket to fit all Series 1, 2 or 3...
Rear hub nut wavy washer in stainless steel.... made by Mb..
0.5mm Magneto house gasket for series 1, 2, 3 & Gp/Dl. made by Mb
Rear hub locking ring screw M7 thats used to fix the rear hub nut lock washer to an Italian type rear...
Chain case Gasket 0.8 mm thick, Crankcase side gasket to fit all Series 1, 2 or 3 crankcase sides (except...
Legshield end cap T nut in stainless steel. sits on the front of the legshields .. 2 needed for series...
MB mag housing stud, this stud fits in the engine case to secure the mag housing. can also be used for...
MB Crankcase side stud, you need 14 for most crankcases. 6mm x 12 - 10 - 1mm in stainless steel, normal...
Easy fit type rear brake cable.. Stainless steel braided wire..
Rear hub plate stud, this stud tholds the rear hub bearing plate. can also be used to convert a gp gear...
MB longer exhaust port stud for round exhaust ports to suit the new longer stronger MB brass nuts.
8mm domed domed Stainless steel wheel nut.
Locating pin that screws in the kickstart piston, tightens up by using an allen key... made by MB..
High spec MB 16x20x20 14 needle small end/little end bearing.
Short inlet stud. 7 x 12-10-12 x 21mm in stainless steel made by MB..
Throttle and gear roller olive bush support clamp in stainless steel.... Two required per handle bar......
MB stainless steel Headset top screw for series 1,3 and Gp/Dl as original... holds the headset top and...
360 degree Metal fuel banjo that turns all the way round for ease of fuel pipe routing, suitable for...
6mm MB Stainless steel grease nipple, used on some Lambrettas on the front hub backplate, the fork links...
Stainless steel rear nyloc nut to suit BGM rear shockers but good for all other makes too.. made by MB...
End plate stud that is made longer one end (the end that locates in the engine casing) to give better...
XL throttle cable inner and outer in GREY ....
Small mag oil seal.. Fits all Series 2 & 3 but not series 1 engines. Mb RaceTour brand..
200cc inlet Gasket that is made f rom a White High strength and fuel resistant gasket material. MB M...
Fork link 12mm half nut for fork link bolts, these are a finer pitch than the front wheel spindles and...
MB crankcase side stud,slightly longer that the standard crankcase stud by 4mm to allow the exhaust bracket...
0.2mm gear cluster shim, This shim is used to shim the gear cluster when fitting 5 speed gear boxes.
Mag sealing plate stud long nut in stainless steel...
Stainless steel Rear light lense fixing screws for late series 2 and series 3.
0.5mm gear cluster shim, This shim is used to shim the gear cluster when fitting 5 speed gear boxes.
Rear hub plain washer used with the recesses on 3 hole locking ring TL 4977