\\r\\n
1.7 mm thick gearbox shim..MB precision gearbox shim remade in hardened shim steel....
S1 & 2 brass bush that fits in the end of the handle bars. MB
MB TZR Handle Bar Grips. TZR type handle bar grips in black. made by MB.
MB Stainless steel Handlebar gear support steel L washer for series 1,2 and late Indian GP
1.0mm thick head gassket for Race Tour 195 (65mm bore) cylinders.
1.0mm thick head gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes....
TS1 reed block gaskets..There are two different size original TS1 inlet gaskets one small and one large,...
Mag side crankshaft dummy bearing bush tool. Stainless steel so it doesn t rust. This replaces a flywheel...
MB mag housing sealing kit. The kit includes: stainless steel sealing plates, gasket, spit rubber grommet,...
MB 3.50 float needle valve made with a viton tip for modern fuels for PHBH PHBL & VH
Rear number plate fixing kit for series 1 & 2 with stainless steel fixings..
MB Quick action throttle wheel that fits all headset ie Series 1, 2, 3 & Gp
Rear brake cable clamp kit in stainless steel made by MB.
Speedo cable olive(bush) in brass that fits on the bottom of the speedo cable near to the hub....
MB Splash Plate for series 2 stainless steel,excellent quality and fit. made by mb....
Tap, 6mm diameter x 1mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Front and...
Tap, 6mm diameter x 1mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
Mb Simple wiring loom to suit most models in Black. Simply plugs into each electrical component and cuts...
Airbox square bolt.. the bolt that fits in the frame that holds the air box in place.... c/w nut and...
MB stainless steel strap that secures the cables to the frame.....
This rubber fits between the mounting point and coil, use studs, nyloc nuts and washers if you can (or...
Bronze bush/bearing for the crown wheel,normally fitted to gp s but they can be fitted to li/SX and TV...
MB Clutch spider shim kit... When using standard or especially Indian clutch spiders and crown wheels...
MB full set of stainless steel standard length studs with nyloc nuts and plain washers to secure your...
Crank fitting/pulling tool Fit the tool over the crank on the drive side side and then use your drive...
0.5 mm MB laser cut aluminium packing plate for 200cc type casings. For use with cranks with 110mm long...
2.0mm laser cut aluminium packing plate for 200cc type casings. For use with cranks with 110mm long conrods...
MB Dellorto PHBH Needle set X7, X7/13, X13, X13/X2, X2, 2 clips, Comes with. X7 needle, taper 20mm, MB...
Top fork bolt on damper brackets in stainless steel for series 125/150 forks series 1,2,3 & Gp/Dl......
Special stainless steel MB designed plate to stop cables been cut through unlike the older Innocenti...
Fork steering bearing top nut for searies 1,2,3, and Gp/Dl... made by MB
MB GP Front brake cable adjuster, completely made in stainless steel....
1.4 mm thick gearbox shim..MB precision gearbox shim remade in hardened shim steel.
MB TZR Handle Bar Grips Black including silver bar ends. made by MB....
0.7mm thick head gasket for Race Tour 195 (65mm bore) cylinders....
1.5mm 225cc thick head gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes. BGM2225HS...
1.8 mm thick head gasket for Race Tour 225 (70mm bore) cylinders with extra bolt holes.
MB shorty reed Inlet manifold screw in stainless steel.
Large mag oil seal tool to drift in the in board (large) magneto housing oil seal . made by MB scoot...
MB Leak down exhaust blanking plate ROUND type.
1.5mm Magneto house gasket for series 1, 2, 3 & Gp/Dl. made by Mb
RT195 Replacement pair of 65mm x 1mm Bgm piston rings for MBGM Race-Tour 195 cylinder kits. Also fits...
Rear hub bearing fitting and removal tool. Use one way and the tool easily pushes out the bearing and...
Rear hub puller for both early series1, 2 and series 3 sx/li/tv/gp rear hubs... made by Mb..
7mm to 6mm oversized stepped stud to repair a damaged 6mm crankcase side in stainless steel.
MB Throttle tube for late series 3 & Gp/Dl (post 1966) in stainless steel .. this is for headsets with...