\\r\\n
Exhaust 7mm Extended brass nut.. made by MB scooters.
Speed clip (4mm) for rear floor plastics (10 needed per scooter)....
Screw for fixing the rear light lense for Gp/Dl only. 2 required.
Rear Lamp Lense Screws for late series 2 and series 3 ....
Split pin in stainless steel for connecting petrol tap lever to the petrol tap and the rear brake pedal...
5mm Roll Pin, 5 x 26mm for handle bar shafts (larger hole Indian type), also used for series 3 panel...
4mm Roll Pin, 4 x 26mm for Italian handle bar shafts.
5x10 pan head screw in ST ST Used to fix legshields to top of horncast....
4x80 cheese head screw in stainless steel, can be used to fit the two halves of a cdi mounting bracket...
4x12 hex set screw in stainless steal, Used to secure the handlebar rod olive clamps and the mag housing...
Stand roll pins in stainless steel 6x40 set of 2.. for series 1,2,3 & Gp/Dl stabds..
4 x 16 raised csk screw in stainless steel, specifically used on horncast grilles, legshield top beading...
4 x 25 raised csk screw in stainless steel, specifically used for floor runner end caps ....
4 x 10 raised csk screw in stainless steel, specifically used for fixing the floor runner strips to ...
5 x 20 raised csk screw in stainless steel, specifically used holding the bridge piece and at the bottom...
5 x 25 raised csk screw in stainless steel, specifically used for fixing the sharks teeth.
5 x 40 raised csk screw in stainless steel .... Headset bottom series 3..
Long engine bar, this fits all models with the large engine mounts.... comes with 2 nyloc nuts and 2...
4 slot head screws (standard Innocenti) that hold the drive side oil seal plate in place. These are the...
Cylinder head stud/fastener kit MB fastener upgrade kit for the MBgm Race Tour cylinder kits. The kits...
Fork link bolt anti shake washers in stainless steel....
Front spindle nut as original in Zink that are made to exact Innocenti drawings, two required for drum...
Rear hub nut in zink with nyloc seal fitted inside,as per original.. Fits Series 1,2,3 and Gp.
Inlet manifold screw in stainless steel bolt inlet manifolds with larger carbs. This bolt is designed...
Headset bolt, MB dual purpose headset bolt which fits both Series 1 and Series 2 headsets. Series 1 uses...
Rear hub nut in zink with nyloc seal fitted inside. Rear hub locking ring. M7 cap head screw. Spring/wavey...
Zink washer that sits in your fork link to hold your spindle (and hub!) in place Two needed for drum...
Engine Bar Nuts & Wavy Washer Set in stainless steal..
Gear selector fork M6 screw but with a smaller head, so you use a 9mm socket instead of a 10mm that you...
Seat fixing set.. This set consists of the following : 4 plastic seat locking plate washers. 4 metal...
5 x 16 raised csk screw in stainless steel, specifically used on running strips amongst other things...
Fork link 12mm half nut for fork link bolts, these are a finer pitch than the front wheel spindles and...
Floor fixing kit for series 2in stainless steel, this floor fixing kit is for series 1&2 150cc type floor...
Floor fixing kit for series 1 & 2 in stainless steel, this floor fixing kit is for series 1&2 125cc type...
Extra long screw in stainless steel for fixing the inner front mudguard on series 1 & 2 Lambretta s.....
Series 3 Li/Sx/Tv and Gp horncasting fixing kit in stainless steel.. MB Product
Series 2 horncasting fixing kit in stainless steel. MB Product
Rear number plate fixing kit for series 1 & 2 with stainless steel fixings..
Headset (handlebar) Fixing kit for series 2 in stainless steel.. MB Product
Switch housing to the handlebars screw in stainless steel....
Legshield end cap T nut in stainless steel. sits on the front of the legshields .. 2 needed for series...
Headset top screw and anti shake washer set for series 2... holds the headset top and bottom togethe...
Headset top screw and anti shake washer set for series 1, 3 and Gp/Dl... holds the headset top and bottom...
Extra thick cylinder head washer in stainless steel...
Split pin for connecting petrol tap lever to the petrol tap and the rear brake pedal clevis pin.... Two...
Flywheel nut & washer (Gp/Dl), only for Gp type crankshaft .. made by Scootopia