\\r\\n
Jack for raising and supporting the engine when changing rear wheel....
Flywheel holding tool that will hold 90% of Lambretta flywheels. It is double ended and will hold normal...
Tool one for pulling crankshafts into place for for ALL Lambretta S1 + S2 + S3 + GP DL + Serveta's models....
BGM Spark Plug socket Knurled finger grip to remove plug when hot 13mm Hexagon head so you can use a...
Spark Plug socket Knurled finger grip to remove plug when hot 13mm Hexagon head so you can use a spanner...
Flywheel Puller for all Italian and Electronic Lambretta Flywheels made in Italy
25 Dellorto and 26/28/30mm Dellorto MB Leak down carb blank.
MB Leak down kit for testing air leaks for series 1, 2, 3 and Gp/Dl. comes with both exhaust blanking...
Tap, 7mm diameter x 1mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
The 4 way engine mount tool will fit direct to your flywheel and in most cases can be used without you...
Tap, 8mm diameter x 1mm fine thread pitch for cleaning out crank. Used for cleaning/tapping threads out....
BGM "O" ring removal tool that can also be used for scribing ....
Extractor tool for removing the CasaCooler bearing support bush X218..
Tap, 3.5mm diameter x 0.5mm thread pitch, Used for cleaning/tapping threads out. Can be used for: Series...
Tap, 4mm diameter x 0.7mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
Clutch Compressor, for series 1,2 & 3. This mounts across 2 studs on the crankcase side, so it lines...
Piston stop tool, universal for Lambretta & Vespa. Plastic ebd version.
Tap, 3mm diameter x 0.5mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
Tap, 5mm diameter x 0.8mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
8 x 1mm right hand thread fine pitch for crankshaft drive side bolt threads series 1,2,3 & Gp
Tool for pulling the layshaft in. Offer the layshaft into the bearing, fit the sleeve locating the allen...
MB Leak down rxhaust blanking plate OVAL/BGM type.
Rear brake pedal and gear selector shaft bush removal Tool.. made by mb scooters
Vape ignition flywheel holding tool for all types of Lambretta Vape Ignition Systems
BGM Clutch holding tool that Holds the inner and outer clutch bell/housing so that the clutch nut can...
Drive side crankshaft dummy bearing bush tool. Stainless steel so it won t rust This replaces a flywheel...
Crankshaft inner bearing sleeve fitting tool.
Mag side crankshaft dummy bearing bush tool. Stainless steel so it doesn t rust. This replaces a flywheel...
16mm piston circlip tool for 16mm piston circlips. Casa Performance X233
Tap, 6mm diameter x 1mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Front and...
Tap, 6mm diameter x 1mm thread pitch. Used for cleaning/tapping threads out. Can be used for: Series...
Crank fitting/pulling tool Fit the tool over the crank on the drive side side and then use your drive...
Double sided flywheel Extractor/Puller for all Lambretta & Vespa models..
Fork spring compressor for series 1, 2, 3 & Gp that is completely easy to use on its own. Simply protect...
Large mag oil seal tool to drift in the in board (large) magneto housing oil seal . made by MB scoot...
MB Leak down exhaust blanking plate ROUND type.
Piston stop tool, universal for Lambretta & Vespa (short reach type)....
Rear hub bearing fitting and removal tool. Use one way and the tool easily pushes out the bearing and...
Rear hub puller for both early series1, 2 and series 3 sx/li/tv/gp rear hubs... made by Mb..
Tap ratchet T handle for larger tap sizes. 5mm to 12mm tap sizes.