\\r\\n
Steering Bearing (top) made in Italy by Casa Lambretta,best quality....for Series 1,2,3 and Gp....
Top steering bearing set for all models. 6 piece set.. From factory, these were originally fit to models...
S1 & early series 2 LI & TV.Bottom steering bearing kit. : lower frame cup : bearing : fork race (depth...
Bottom steering bearing kit for LI, SX, TV, DL & GP. Deep bottom steering kit (total cone depth is 46mm)...
Steering/fork bearing set (top & bottom) for series 1,2,3 and Gp/Dl .
Small end needle bearing (for piston) Lambretta 50cc + 75cc models. NON original size measurements: Internal...
Granturismo Small end conversion bearing KV16x22X22 Conversion Bearing for a 22mm con rod to take a 16mm...
Granturismo Small end conversion bearing KV16x22X20 RB TS1 Conversion Bearing for a 22mm con rod to take...
Crankshaft small end bearing (for original conrods) for Lui and J models. Casa M240a
High spec Ina 16x20x20 14 needle small end/little end bearing....
CP105 Crankshaft small end bearing (for cp105 cylinder kits) for Lui and J models.
CP105 Crankshaft small end bearing (for cp105 cylinder kits) for Lui and J models.
High spec MB 16x20x20 14 needle small end/little end bearing.
Small end/little end bearing 13 roller silver caged 14x20x20
Small end/little end bearing 20x20x16 made in Germany by INA these are very good quality
Small end bearing 16x20x22mm fot GT pistons and others that require a wider bearing, Yamaha wide type....
2nd Oversize rear hub bearing to be used in engine casings that the rear hub bearing aperture is slightely...
ist Oversize rear hub bearing to be used in engine casings that the rear hub bearing aperture is slightely...
3rd Oversize rear hub bearing to be used in engine casings that the rear hub bearing aperture is slightely...
Rear hub bearing made by Scootopia. We think these are the best.
Rear hub bearing retaining plate shim, the thinner one .. S1, 2, 3 & Gp/Dl 858
0.9 / 1.2 Mb rear hub bearing plate in stainless steel and has a recess on one side of 0.9mm recess on...
0.3mm Mb reear hub bearing plate in stainless steel and is flat on one side.
0.5 / 0.7 recessed Mb rear hub bearing plate in stainless steel
Mb reear hub bearing plate set of 3 in stainless steel .
Mb rear hub bearing O ring seal.. fits in the recess in the bearing to form a better seal..
Rear axle layshaft bearing (rear hub bearing)for all J Range and Lui Vega/Lui75 Cometa models... CASA...
Rear hub bearing double row with snap ring, felt & retaining plate. especially used with AF 5 speed gearbox...
Rear hub bearing BGM with oil seal for series 1, 2. 3 & Gp.
Rear hub bearing for when fitting Octopus rear hubs. This bearing uses a special thinner type oil seal...
Mag house bearing spacer ring for li/lis/tv/sx bearings.
L shaped washer sits inside your magneto housing and holds one of the oil seals in place....
Flywheel side bearing 6204 (early prod.) for 3 speed 50cc Lambretta J models. Early models use this type...
Layshaft needle roller bearing. A high quality layshaft needle bearing. made by SKF
Layshaft needle roller bearing. A high quality layshaft needle bearing. made by INA
Gear cluster bearing, Ina high quality gear cluster needle bearing.
Gear cluster needle bearing...This sits in underneath the gear cluster....
3 Piece gear cluster bearing and bush set, comprising of: Gear cluster bearing. Bush. Shim (fits under...
Front Hub bearings (Fag) & oil seal set for Series 1,2,3,Gp, Lui & J
Front Hub bearing, FAG best quality....for Series 1,2,3 and gp.
Flywheel side / Mag bearing x803 mag houses. for Lui, Vega, Cometa and J X803B
Li/Sx/Tv crank type only, Fag flywheel bearing..
Gp/Dl FAG high load flywheel bearing for all Gp/Dl type crankshafts..This bearing will fit GP taper type...