\\r\\n
Mb rear hub bearing O ring seal.. fits in the recess in the bearing to form a better seal..
Mag house bearing spacer ring for li/lis/tv/sx bearings.
L shaped washer sits inside your magneto housing and holds one of the oil seals in place....
Rear hub bearing retaining plate shim, the thinner one .. S1, 2, 3 & Gp/Dl 858
Steering Bearing (top) made in Italy by Casa Lambretta,best quality....for Series 1,2,3 and Gp....
Shim that sits behind M217 needle roller bearing on crankshaft. CASA 909
Steering/fork bearing set (top & bottom) for series 1,2,3 and Gp/Dl .
Front Hub bearing, FAG best quality....for Series 1,2,3 and gp.
High quality Clutch needle bearing.. Used as standard on Li, SX, TV models.. two needed
Gear cluster needle bearing...This sits in underneath the gear cluster....
0.3mm Mb reear hub bearing plate in stainless steel and is flat on one side.
Brass bush/bearing with oil grooves for the crown wheel,normally fitted to gp s but they can be fitted...
Crankshaft small end bearing (for original conrods) for Lui and J models. Casa M240a
0.5 / 0.7 recessed Mb rear hub bearing plate in stainless steel
0.9 / 1.2 Mb rear hub bearing plate in stainless steel and has a recess on one side of 0.9mm recess on...
Small end needle bearing (for piston) Lambretta 50cc + 75cc models. NON original size measurements: Internal...
Layshaft needle roller bearing. A high quality layshaft needle bearing. made by INA
High spec MB 16x20x20 14 needle small end/little end bearing.
Drive Side Bearing for Lui 50 J50 J100 J125 3 speed ... M219
End plate bearing high quality for B + C + LC + J + Lui + Vega + Cometa
Gear cluster bearing, Ina high quality gear cluster needle bearing.
Layshaft needle roller bearing. A high quality layshaft needle bearing. made by SKF
Small end/little end bearing 20x20x16 made in Germany by INA these are very good quality
Small end/little end bearing 13 roller silver caged 14x20x20
CP105 Crankshaft small end bearing (for cp105 cylinder kits) for Lui and J models.
Granturismo Small end conversion bearing KV16x22X20 RB TS1 Conversion Bearing for a 22mm con rod to take...
Granturismo Small end conversion bearing KV16x22X22 Conversion Bearing for a 22mm con rod to take a 16mm...
Main Drive Bearing Fag comes with extra seal fitted one side for extra protection.. fit with seal facing...
3 Piece gear cluster bearing and bush set, comprising of: Gear cluster bearing. Bush. Shim (fits under...
Crankshaft flywheel side bearing (for version 1 cranks) for 3 speed 50cc made by SKF.. M218z
Front Hub bearings (Fag) & oil seal set for Series 1,2,3,Gp, Lui & J
Bronze bush/bearing for the crown wheel,normally fitted to gp s but they can be fitted to li/SX and TV...
CP105 Crankshaft small end bearing (for cp105 cylinder kits) for Lui and J models.
Small end bearing 16x20x22mm fot GT pistons and others that require a wider bearing, Yamaha wide type....
Flywheel side bearing 6204 (early prod.) for 3 speed 50cc Lambretta J models. Early models use this type...
Bronze clutch bush with an oil groove machined in it...
INA clutch needle bearings..2 per engine.. SOLD IN PAIRS ....
High spec Ina 16x20x20 14 needle small end/little end bearing....
Mb reear hub bearing plate set of 3 in stainless steel .
Gp Flywheel Brass caged bearing for all Gp/Dl type crankshafts. This bearing will fit GP taper type crankshafts...
Rear hub bearing made by Scootopia. We think these are the best.
Bottom steering bearing kit for LI, SX, TV, DL & GP. Deep bottom steering kit (total cone depth is 46mm)...